This is a plaster surface pool. It’s actually fairly large. It’s probably over 25,000 gallons likely close to 30,000 gallons. The pool overall is a consistent depth with approximately 3 1/2 feet seen in the shallow ends on either side and approximately 6 feet in the middle. The surface overall is in fairly good condition which I would estimate its age between seven and 15 years old. The surface has many markings and scratches on it making it difficult to identify actual cracks. I have counted over 50 scratches approximately. I do see some calcium fissures developing in the bottom of the pool mostly seen in the middle and middle east side of the pool. This is generally indicative of shell integrity potential issue especially as I am seeing more than five typically these calcium fissures indicate a minor weakness in the shell and while these issues may not be needed to be addressed now they will likely need to be addressed at time of next re-plaster or in the next 5 to 15 years which may consist of opening up these areas reinforcing rebar and gunite. Otherwise standard wear pattern seen but non-standard scratches seen throughout with no real rhyme or reason. If the calcium fissures were not present I would estimate the surface has another 15 years of life left at best while the fissures themselves don’t necessarily dictate longevity of life rather water loss developments due to erosion potential through these fissures would therefore it may knock down potentially five years from that 15 year number. The cost to plaster pool this size would likely run between $12,000 to $15,000 when that is due which it will be due at time of water loss being seen.
Estimated cost grouping: Re-plaster $12,000-15,000.

The waterline tile is all present none missing. I do see some minor gaps especially on the west side of the pool that have likely formed and have been addressed overtime with mastic in the past 1 year possibly the past 1 to 3 years it is present throughout the entire pool so this is likely an ongoing compensation as far as issues present. One is located on the spill over overfill line appear that the tile may be splitting right down the center and therefore may need attention in the near future. At the same time it would be wise to consider updating some of the mortar where that is seen inside the skimmer throat at the opening corners and where the skimmer itself meets the plastic to the tile mortar connection. This would likely need to be done in the next 1 to 5 years or less at a cost of less than $500. Otherwise the waterline tile does not have any considerable calcium buildup and no other areas of concern seen except for on the other side of the pool there is a fill port and it also appears that there may be a split on this tile as well. This should also be able to be easily repaired at that time of tile service.
Estimated cost grouping: Waterline tile mortar and repairs less than $500.

The water quality is due for adjustments. It does appear that the Cyanuric acid level is likely too high indicating that we are going to be due for a partial drain ($250) that coupled with pH and alkalinity being elevated as well as chlorine being elevated indicates that there is organic matter living in this water and therefore treatments will be necessary likely less than $375 in service and treatments to remove organics plus an extra $250 or less to do a partial drain would be a recommendation at this time. Also note that CYA and calcium hardness levels are high indicating that this water may be old and therefore a complete drain and refill may be the wise choice if this water is all original especially with animal use.

Estimated cost grouping: Treatments $375 plus partial drain $250.

Larger 10” cover present, older due for updates ($200 or less). Note this is not a VGBA compliant cover - the drain itself can be updated at time of next Re-Plaster = $1k+

The skimmer show signs of chlorine cookie abuse, thus degrading the quality of the skimmer itself, and there is a small split at the top of the skimmer circle edge, that is luckily not in the waterline yet. At time of next RePlaster it may be wise to consider updating the skimmer ($1k+) due to issues seen.

Otherwise, recommend adding a new float, float o ring, weir door, and lid soon ($400 or less).

Recommend a new tail, tires, bearings / wheels loose soon, and possible new hose segments + backup valve (less than $105).

Very low flow auto fill - unusual, working, but due for minor leak service to the fill mechanism ($125-250 or less).

The pool light doesn’t look super old but does appear to have light condensation inside the light lens approximately 20 to 40% indicating that it is due for updating which requires a replacement can. A replacement can is anywhere from $200 up to $1250 depending on quality and $400 for install installation.

Pressure is high 12, at 2600 rpm. indicating that the filter elements are due for service at $150, and at that time, checking to see if the elements are due for replacement at around $400 + liquid filled pressure gauge ($50) and potentially other O-rings that are due to be updated every 5 to 10 years at less than $100

This pump is in working condition with no damage scene other than the conduit which is heavily sun exposed, and likely due for replacement soon ($100 or less)

Note that the pump is in relatively direct sunlight, the majority of the day indicating that it is essentially getting cooked when I open up the back hatch lid to expose the LED screen. It is showing heat wear present.

Non GFCI breakers present recommend updating via electrician ($350+) and parts $300+

The plumbing and fittings section we had is due to be covered from the sun using UV mesh for less than $50 right away. Additionally the pad is due to be repainted and re-labeled for less than $200. There is a leak on one of the return valves that is due for service at less than $300. There’s a leak on the pump return union that is due for service at less than $200. Additionally recommend installing an optional check valve on the suction side of the plumbing of the pump to help prolong life of this pump at less than $400 installed.
Estimated cost grouping: UV mesh $50 plus pad repaint/relabel $200 plus return valve leak $300 plus pump return union $200 plus check valve $400.