The surface is older and showing its age with cracking and rebar stains present throughout. I would classify this as due for attention now vs later due to the water loss that’s present.

Many blemishes present throughout; cracks, rust stains x 9, and gunite cracking outside water throughout / structure in west end.

This pool is due to be corrected in several locations both inside the pool and outside. The estimate construction value to re-hab this structure / surface situation would likely run 15-40k+ and it should include opening up the gunite structure in several locations ($5-15k+) , re shooting gunite ($5-10k+), and then re surfacing the pool / basins ($9-15k). Total cost would be confirmed after progressing through exposing sub surface issues, therefore exact costs likely cannot be confirmed ahead of time vs during the remodel project.

New fresh water. Low chemical residual likely due to water loss being present (seen in south west shallow end). Cost to rebalance this pool or a fresh pool will run $80-250. And a needed phosphate treatment $85.

The skimmer and signs of high chlorine cookies being used at one time for prolonged times. Older.

The skimmer float also has a broken diverter. And should be updated ($50) soon. Also missing weir door ($50). Recommend both.

The main drain cover should be updated due to age and condition ($100).

Note is does appear that this pool is more than 5-10 feet in elevation change below the pool equipment making it progressively more difficult to operate this body of water predictably through this pump setup (hence the double check valves on the filter pump and filter pump cannot be ran higher than 2500-3000 rpm’s without creating cavitations inside the pump).

The cleaner is constantly getting itself jammed into a corner, or far side of pool. Given its new but due to hose length and pool bottom type I wouldnt anticipate much from this “bottom cleaner” due to the situation. I’ve seen other pools LIKE this pool (Natural Designs) smoothed with plaster vs having this exposed gunite look, as a future potential solution. Otherwise bottom cleaning in this pool will not be ideal vs having a second skimmer added coupled with a variable speed pump running to help assist with surface debris removal BEFORE it falls to the bottom. A second skimmer may be able to be much easier to be added at resurface / restructure time.

The fill was not checked as it appeared to have not been accessed for some time, and I didn’t want to potentially damage the already damaged / shattered stone. This fill canister likely needs to be opened, cleaned, and the fill updated ($125-250+)

I was unable to get the light to function. Still the light does appear to have some minor condensation present inside the light lens, and therefore should be updated for safety ($575 light can , $350 labor)

The pressure is relatively low, generally indicating a bad gauge or low flow due to a less than ideal elevation issue.

The filter is relatively new and in good condition. Still I’d recommend a new gauge to confirm if issue is present ($50).

This pump is in a difficult position (hence the double check valves on the filter pump and filter pump cannot be ran higher than 2500-3000 rpm’s without creating cavitations inside the pump) therefore this pumps lid o ring and suction side check valves will need a high degree of attention to ensure damage prevention to this pump occurs.

Otherwise this pump is relatively new without issue other than a dry lid o ring / check valve connection (recommend service to confirm - $50).

Also the back screen protector is off on the ground and should be re attached ($2).

The vacuum gauge does not appear to be functioning either, recommend replacement ($50)

Working condition. Like new. Without issue.

It appears this pump is in working condition; new debris present inside the pump basket. Still I was unable to give this pump power and confirm its status. IF the motor / drive has failed expect a cost of $1250+ to repair, or replace with like pump $2800. But it is more likely there’s a secondary switch present that activates this function.

Timer appears to have been worked on recently, old breakers present, recommend confirming why the waterfall pump does not turn on and function using switches present.

Additionally the pool light does not appear to be integrated into this either ? Could not locate a switch for that as well.

Still the breakers are new gfci and in like new condition. If repair is required to resolve light and waterfall pump expect a cost of approx $550 for an electrician to
Visit and replace breakers / add switches.

The Valving present has been recently updated. It can be painted for uv and re labeled if desired ($50).