The surface of the pool has some missing sections on the shallow end steps, specifically the edges. Generally seen on pools older than 15-20 years. The wear is likely newer as its white vs the remaining surface has a blue tint.

In the shallow middle end west I do see some excessive wear markings.

The surface of the pool also has a copper sulfate stain present throughout the surface fairly uniformly. The staining is also present on the plastics scene in the pool, specifically the main drain cover of the spa.

The return jets in the spa also have some excess buildup of the plaster for unknown reason Other than to show us that these jet heads are the same as the original.

In the deep end of the pool, I am seeing rust stain, closest to the main drain approximately 25 of them the size of a dime.

I see excess wear in the deep end, but could just simply be surface staining.

There appears to be a potential crack on the top step of the underwater fall. Difficult difficult to determine since there are scratches present also on this top step. The location of the blemish is 3/4 of the way north directly below the three red circle stains.

There is some raised masonry block on the east side of the pool. Some caps of the block are loose - and in the corners I am seeing cracks present. Recommend re mortaring / repairing these sections to assist with longevity ($2500-5000k+).

Additionally the spa spillover has some issues present - expect a cost of $1k+

The water quality has high pH and alkalinity otherwise all levels are ideal ($25). Note that there is black algae present in some areas of the pool ie steps and deep end / lower wall. It doesn’t look fully impacted yet - recommend treatments to help eliminate ($400).

The main drain in the spa appears to be too close to the cover. Recommend modification for safety ($100+) . The pool cover is difficult to confirm due to depth, but appears to be more than 3” away.

I feel the surface is between 5-10 years old on smoothness but in appearance 12-18 years old. And therefore the covers x 2 are due for updates ($100x2) for safety.

The skimmer is older. It is missing its internal float door. I would recommend finding the appropriately sized float for the skimmer or modifying it to allow main drain section to occur ($300+ Service).

The Phil operates. It’s at the north section of the pool at the niddle corner of the house. It is leaking during use recommend updating ($250+)

The pool light appears to have rust not only inside the light lens, but also on the metal ring recommend updating for safety $750+

The filters heavily sun worn approximately 10 -15 years old. Recommend updating the pressure gauge ($50) and servicing the filter ($150+) due to black algae conditions and high psi. Also it is likely the elements are going to then be due for updating ($500+).

This pump is like new without issue. Note that it is slightly oversized for the Plumbing application and should not be ran past 80% speed or flow. Recommend modification to the programming to accomplish this ($125).

The booster pump installed appears to be approximately five years old going on 10, but he’s not turning on wind powered. Additionally, the hoses have some sun damage to them proximately 40% damaged on the suction hose. It is likely that this pump has expired due to being ran without the main filter pump. Cost to update this with a new pump is $1800 installed.

Approx 10 years old. Working. Recommend adding a drip leg ($400) to the gas line as required and an optional heater bypass $750 to prolong the life of this older heater.

Also note the heater is more than 4 feet USA standard but not more than 6 Canada standard away from the openable window. Note inhalation of heater exhaust is very hazardous and virtually un detectable - unless with an approved device. Recommend installing such alarm ($50+) inside the window / bathroom.

The timer board is not ideal. Its timers are loose and terminals exposed on the lower timer. Additionally, the breaker bar has some type of corrosion that will limit the panels ability to use power. Recommend a new updated panel ($750+) and attention to exposed conduit. Also recommend updating the breakers to GFCI for safety ($400+)

Working without issue. Recommend covering from UV but first re painting and labeling ($300).