The surface has blemishes present throughout.

Around all of the bottom returns, there is missing plaster. This may require repair soon if leaks begin to occur ($1000+).

The spa spill over has some blemishes possible water markings? likely from filling the spa during initial plaster start up.

The shallow end steps has checked cracking present likely from long-term sun exposure.

In the southwest section of the shallow end there appears to be a crack or check crack present pictured.

The surface appears to be approx 13-15 years old

The tile is in good condition overall no loose or missing.

There is a piece of the concrete coping missing in the north east section of the pool. This is a visual issue only that can be repaired for $200.

There is calcium buildup present throughout the pool and on the spot spill over recommend removal at approximately $650- 750.

Also know that throughout the pools deck structure there are cracks on the steps leading up to the spa and around the spa on the concrete deck on both the north and south side.

There is no chlorine present in the pool and a high pH and alkalinity level. Also recommend increasing the cyanuric acid levels ($250). The water quality is indicating that water loss may be present. Also there appears to be sections of black algae present around the steps, pool light, and between some of the tiles, approx cost to treat is ($250).

There are four main drain covers two in the pool and two in the spa that will need to be updated due to age and condition ($88x4). There are also three return covers that should also be updated at the same time and six return jet heads in the spa ($600).

The scammer shows signs of chlorine abuse mostly at the bottom of the opening. Also it does appear that the mold of the skimmer gives a deceiving tone that there is a crack present on the east side however it is at the exact location of the mold on both sides of the skimmer therefore it is not likely a crack but instead just a mold marking.

Recommend updating the float and float O-ring ($100).

The bottom cleaner is in working condition however it is older than 10 years and it will need new tires soon and likely one or two additional hose floats ($105+) also recommend installing an in-line leaf basket ideally Pentair for best operation ($105) + install

The auto fill float is in working condition however canister cannot be accessed due to its handle not allowing a finger to be entered into it to remove it, recommend repair to resolve ($125+)

Upon accessing the auto fill canister it does appear that where the float screws into the plastic body there is consistent operation of the water coming into the fill canister likely over filling the pool on a regular basis it is either cracked at its inlet or not enough threading sealant is applied to the auto fill float head recommend service to resolve and identify ($125+).

Note a whole new float canister installed is $2500+

There appears to be some water presence inside the light lens recommend updating for safety ($750+).

There appears to be some water presence inside the light lens recommend updating for safety ($750+).

Filter is due to have its tank O-ring serviced a new pressure gauge and likely new filter elements installed if the elements haven’t been replaced in the past 2 to 5 years ($800). It is nearly impossible to tell the current pressure of this filter but I would assume it is it approximately 10 to 15 psi at 2500 RPMs.

The filter pump is working however it is due for service specifically a new pump lid lid O-ring and likely union O-rings as well ($500).

Note that the motor body shows signs of corrosion to the drive and motor itself indicating that issues have been present likely with overheating or salt water dripping on the components for prolonged periods of time. In general this pump is approximately 17 or more years old and due to its current condition I would estimate its remaining life is between one and five years. A replacement pump of this kind is approximately $2700 installed.

The heater is in fair / good working condition without issue at this time. I do not like that the panel antenna communication wire is directly over the exhaust vent recommend moving this ($100). Additionally the heater shows signs of heavy corrosion on the metal heat exchanger leading out of the heater and I would only anticipate this unit working for another 1 to 5 years due to its current age and condition. The cost to update this heater is $4900 installed.

The panel is in working condition recommend updating the breakers to variable speed compliance and the pool light main breaker to GFCI if possible ($300).

Note that it is approximately $600 to add on phone connectivity plus installation which will include programming ($675) = $1275

The salt cell is manufactured in 2010 indicating that the cell itself is likely due for replacement recommend updating ($850+ Install $350). Also note that UV plus o zone is a superior alternative option ($2100+ installed).

Revolving installed shows signs of heavy solids and or high chlorine abuse and will require servicing to all valves replacing four check valves and servicing unions. Expect a cost of approximately $1500 to perform. This will also include painting and labeling the entire equipment on correctly.