Expert Level Pool Inspections
Print Friendly Edit

8450 Spruce Meadows Lane,, Granite Bay,, CA (9:00 AM - December 29, 2020)

Google Maps

Front Of House Pool Spa

Equipment Pad

Equipment #1 Equipment #2 Equipment #3 Equipment #4 Equipment #5

Safety Fencing Condition: N/A $

Safety Fence #1 Safety Fence #2
Style Location
Wooden
Safety Fencing Notes
Access was through home
Safety Fencing Additional Notes

Pool Safety & Drowning Prevention:

As of 2018 California Building Code (CBC) for Swimming Pool Safety Barriers / Enclosures Per Health & Safety Code 115922(a), the swimming pool and/or spa shall be equipped with at least two of the following seven drowning prevention safety features. Please provide a second feature. Note that a fence along the property's perimeter is not listed.

1) an enclosure that meets the requirements of Section 115923 the swimming pool or spa from the private single-family home; and isolates

(2) removable mesh fencing that meets American Society for Testing and Materials (ASTM) Specifications F2286 standards in conjunction with a gate that is self-closing and self-latching and can accommodate a key lockable device;

(3) an approved safety pool cover, as defined in subdivision (d) of Section 115921;

(4) exit alarms on a private single-family home's doors that provide direct access to the swimming pool or spa (provided on drawings);

(5) a self-closing, self-latching device with a release mechanism placed no lower than 54" above the floor on the private single-family home's doors providing direct access to the swimming pool or spa;

(6) an alarm that, when placed in a swimming pool or spa, will sound upon detection of accidental or unauthorized entrance into the water. The alarm shall meet and be independently certified to the ASTM Standards F2208 "Standard Safety Specification of Residential Pool Alarms," which includes surface motion, pressure, sonar, laser, and infrared type alarms. A swimming protection alarm feature designed for individual use, including an alarm attached to a child that sounds when the child exceeds a certain distance or becomes submerged in water, is not a qualifying drowning prevention safety feature.

(7) other means of protection, if the degree of protection afforded is equal to or greater than that afforded by any of the features listed above and has been independently verified by an approved testing laboratory as meeting standards for those features established by the ASTM or the American society of Mechanical Engineers (ASME).

TWO DEVICES I.E.; "DROWNING PREVENTION SAFETY FEATURES" WERE NOT OBSERVED.

Pool Surface Condition: OPINION: The plaster condition shows signs of normal wear for the age of the pool. When it comes to repalster the pool typically re-tiling is also considered. The Estimated Retail Construction Value (ERCV) replacement cocts should range between $5K to $7.5K depending upon the extent of efforts employed in addressing the total or parcial removal of the existing plaseter. $7500

Surface #1 Surface #2
Estimated Gallons Surface Type
15K - 20K Gallons Plaster
Dimensions Damaged Estimated Surface Age
13.5' by 35' 10-50% 12-48 Months
Pool Surface Notes
There are some small areas of staining or discoloration, The surface is slightly abrasive and not as smooth or as new and will allow more organic matter to grow as a result of the slightly abrasive surface
Pool Surface Additional Notes

Plaster and Chemical Attack:

Cementitious surface coatings are susceptible to chemically and pH aggressive swimming pool water or to any chemical that is capable of deteriorating the cementitious materials of a surface coating.
Swimming pool water that is not in Ideal Range of acceptable tolerance (or “balanced”) as in accordance with the ANSI/APSP Standards is considered to be detrimental to cementitious surface coatings.
Depending on the direction of the imbalance a coating can either be stained or etched. Often, both staining and etching are exhibited on the surface of a coating as the pool water fluctuates from one extreme to the other.
There are visible signs of salt crystallization, surface efflorescence, or cracks that are emitting efflorescence or salt deposits which are common to a coating in contact with a positive saturation index (+ LSI), or “scaling” condition.
If the water is capable of leaching cement compounds from within the surface coating, then that water is in a negative saturation index (LSI), or "aggressive" condition.
If care is not taken to ensure that the water of a swimming pool is kept in an Ideal Range that is considered by ANSI/APSP to be balanced, and further that a sufficient amount of carbonate alkalinity buffer is constantly present, then the cementitious surface coating should be considered susceptible to damage from that water and deterioration may result.
Water-soluble salts, acids, or ions such as sulfates, chlorides, and carbonates, can be transported into a cementitious surface coating and react with the cementitious compounds. The resulting chemical reaction between the cementitious compounds and these salts, acids, or ions, in the presence of water, can cause deterioration to the coating. Acidic water aggressively attacks and dissolves cementitious surface materials.
Water that is low in hardness, or soft water, can cause leaching of certain compounds of the cement, especially calcium hydroxide.
For more information about the National Plastering Council's re-plastering recommendations please go to their website: https://www.npconline.org

Tile Condition: Good$

Tile #1 Tile #2
Water Line Tile Linear Footage Tile Water Level Tile Linear Footage
N/A N/A 110
Tile Type Calcium Build-Up Loose or missing tile?
Ceramic N/A or none
Mastic Repair
(ERCV) Concrete / Mastic Repairs $3.5K to $4.5K
Additional Mastic Repairs

STATEMENT TILE REMODELING / REPLACEMENTS;

The adherence of tile or veneer products being applied during the re-tiling process of an existing swimming pool / spa and or water feature are subject to the status of the gunite shell's existing conditions. These conditions are unknown and outside the awareness of the current costs evaluations. Unknown conditions may exist that involve the effects of water saturation / penetration deterioration to the Bond Beam and or surfaces that are designated to have topical products reapplied. Repairs and remedy of such conditions are not part of any estimated costs assessments as they cannot be known until forensic investigation determines whether or not these will affect the re-applying process of the topical applications.

Therefore, until removal and discovery is performed of the existing underneath conditions, we cannot fully confirm that the intended work scope will not expand beyond the scope that’s been estimated. If this becomes a requirement an estimate will be submitted for approval prior to commencing with the additional repairs.

OPINION: The south east side of the pool concrete decking has lifted up approximately 1/2" to 3/4". It isn't definitively apparent as to why this has occurred including an original installation oversight in quality control.

Our logic here would be to eliminate the Redwood tree roots as a source, as the concrete's outer perimeter wall doesn't reflect a corresponding lifting.

Expansion and Contraction in Concrete Construction (PEI):

Most of us in the swimming pool construction industry know that many materials expand and contract with temperature change.

How many of us know how important proper trade practices are in minimizing problems due to temperature caused expansion and contraction, is another story?

For example, concrete is one of the most highly utilized materials in our industry today, yet the industry consistently sees swimming pools damaged by expansion and contraction of adjacent concrete flat-work.

The most important bit of information to remember is the expected expansion in concrete caused by temperature change. Between the heat of summer (pool deck surface at 130º to 140º) and the dead of winter (pool deck surface at 30º to 40º) we can expect at least a 100º temperature change.

The critical number to remember is that a 100 foot wide section of concrete will expand approximately 3/4 of an inch with a 100º temperature change. The expansion in lesser widths of concrete can be easily determined by proportioning the 3/4“ per 100 feet.

The force of expanding concrete is very high and can easily shear off the coping or bond beam without properly installed isolation joints.

Mastic Joints (PEI):

The mastic joint between the swimming pool concrete decking and the pool coping/bond beam is an extremely important component of a swimming pool and must be properly installed. The purpose of this joint is to isolate concrete deck movement from the pool coping/bond beam assembly.

As outlined above, concrete flat-work including pool decks expand and contract with temperature change (up to 100° of variation can be expected).

Without the installation (and proper maintenance) of a flexible mastic joint between the swimming pool decking and the pool coping, movement caused by expansion and contraction of the pool deck will frequently cause dislodged coping, tile and horizontal cracking in the water line tile, and in some cases lifting of the decking itself.

This mastic joint must extend the full depth of the concrete decking so that no portion of the concrete deck can apply pressure against the coping or any portion of the pool structure.

A design diagram (Construction Details) should be provided when proposing any replacements and or repairs in order to
direct proper construction joint techniques in order to not suffer future ramification from improper joint techniques.

As indicated in this narrative, an accompaniment of such a diagram establishes measurable standards that can come from design assistance. These efforts in turn define the clearer objective to be met from the responding solicitations, quoted pricing and performances from the selected Contractors.

In order to mitigate the potential of the dislodging of the pool coping, deck lifting / settling, horizontal cracking in the waterline tile and shearing of the bond beam from improper installation of the mastic joint, preparations need to be employed.

Proper installation of the mastic joint is normally the responsibility of the concrete pool decking installer and unfortunately this component of the swimming pool's construction has more to do with aesthetics than the building code compliance being critiqued by officials.

The lack of adequate maintenance of the mastic joint may result in a loss of expansion protection and can cause the same problems that are experienced without the installation of the mastic joint
.
Cantilevered Concrete Pool Decking (PEI)

Cantilevered concrete pool decking must also be properly installed to isolate concrete deck movement due to temperature expansion and other causes from the pool coping/bond beam assembly.

And again, the proper construction techniques basically requires the leveling of the top of the bond beam and then the installation of a bond breaker or slip joint on top of the leveled beam prior to pouring the concrete deck.

This can be shown on an accompanying diagram when plans are prepared By not following the proper construction techniques, the waterline tile may become partially applied to the cantilevered deck (which will result in horizontal cracks in the tile) or deck movement may shear off the leveling mortar course or the top of the bond beam.

Equipotential Bonding

No steel reinforcing should be extended from the bond beam into the pool deck. Further, the new cantilevered concrete deck should have no direct contact with the bond beam of the pool especially immediately behind the bond beam.

Bonding of the Leveling Course of Mortar
Reoccurring horizontal cracking and dislodging of the water line tile can also be caused by the un-bonding of the mortar or concrete layer used to level the top of the bond beam elevation prior to coping or cantilevered concrete deck application.

This un-bonding, most likely, has been caused by improper construction techniques used in the application of the mortar or concrete layer to the top of the lower bond beam elevation.

It is very important that correct procedures be followed to assure proper bond of this mortar course to the existing bond beam.

In order for a property Owner to become the beneficiary of such information, it is imperative that directions are provided for Contractors to follow.

"Construction Details" and design direction offer recommendations for how to approach the correct construction techniques.

City / County Building Inspectors are generally only concerned with attaining proper bonding of new materials such as masonry, tile, gunite and concrete to existing similar materials as that of being "code compliant".

Here are a few things that get missed absent the peripheral view's greater appreciation for the cause and effects mentioned above;

1. Existing surfaces must be sound, free of defects, clean and free of bond inhibiting materials.

2. Existing surfaces must be roughened by chipping or other suitable means to provide an open pore structure. All loose, cracked or deteriorated materials must be removed.

3. Clean existing surfaces by water blasting.

4. New material should be applied over cement paste or another approved bonding agent, which has been brushed onto the substrate (existing material) for absorption into the pore structure. The new material shall be applied before the cement paste or other approved bonding agent “skins over” or starts its “setting stage.”

5. Saturated surface dry condition of the substrate shall be maintained to prevent premature drying of the bonding paste.

Following these recommended practices will minimize problems in attaining proper bonding between these materials and will provide quality results.

* END OF NARRATIVE*

The mastic (Deck-O-Seal) material that has been applied in between the precast coping and the concrete decking fills a joint and this is a location that has the potential for water intrusion under the decking, especially if this mastic is not maintained to a good standing periodically.

It is apparent that the mastic needs some attention / repair and it would be our recommendation to remove the old mastic material and re-apply it per the MFG.'s directions.

Additional Tile Notes

STATEMENT TILE REMODELING / REPLACEMENTS;

The adherence of tile or veneer products being applied during the re-tiling process of an existing swimming pool / spa and or water feature are subject to the status of the gunite shell's existing conditions. These conditions are unknown and outside the awareness of the current costs evaluations. Unknown conditions may exist that involve the effects of water saturation / penetration deterioration to the Bond Beam and or surfaces that are designated to have topical products reapplied. Repairs and remedy of such conditions are not part of any estimated costs assessments as they cannot be known until forensic investigation determines whether or not these will affect the re-applying process of the topical applications.
Therefore, until removal and discovery is performed of the existing underneath conditions, we cannot fully confirm that the intended work scope will not expand beyond the scope that’s been estimated. If this becomes a requirement an estimate will be submitted for approval prior to commencing with the additional repairs.

Water Quality Condition: Good $

Water Picture #1 Water Picture #2
pH Level Free Chlorine Total Chlorine Cyanuric Alkalinity Calcium
6.8 - 7.2 (Ideal) 2 - 5 (Ideal) 2 - 5 (Ideal) 20 - 50 (Low) 45 - 70 (Ideal) 250 - 400 (Ideal)
pH Level Details Free Chlorine Details Total Chlorine Details Cyanuric Acid Details Alkalinity Notes Calcium Notes
Algae present? Foliage found in water? Water loss present?
No No
Additional Water Quality Notes

NOTE: See Salt / Chlorine Generator note
(ERCV) $1K to $1.5K

Skimmer & Main Drain Circulation: Poor $138

Drain #1 Drain #2 Skimmer #1 Skimmer #2
Water Flow Through Skimmer Water Flow Through Main Drain Skimmer Float Valve
Poor 1
Pool Skimmer QTY Spa Skimmer QTY Pool Main Drain QTY Spa Main Drain QTY
1 2 2
VGBA Compliant Drain Covers
No / Could Not Determine / Recommend VGBA Compliant Cover ($88)
Skimmer & Main Drain Details
The first skimmer is in *working* condition however it is missing its *float valve* ($50)

Skimmer & Main Drain Additional Notes

Virginia Graeme Baker Pool and Spa Safety Act Information

On December 19, 2008 the Federal Virginia Graeme Baker Pool and Spa Safety Act (VGBA) became effective. The VGBA requires all pool drain covers manufactured or sold in the United States to comply with new entrapment standards. VGBA also requires owners of all new and existing public swimming pool and spa suction outlet systems to install safety equipment, including ASME/ANSI A112.19.8 certified suction outlets and covers, designed to prevent entrapment.

Currently the pool’s drain cover devices do not meet the safety requirements and should be replaced when the pool is replastered.

Bottom Cleaner Condition: Good $275

Cleaner #1 Cleaner #2
Bottom Cleaner Brand Bottom Cleaner Model
Bottom Cleaner Additional Notes

OBSERVATION: The pool cleaned works parasitically off of a shared and partially open isolation 3-way valve. The valve is located just past the filtration pump's discharge line. The Cleaner is a pressure side style and appears to be in working order.

RECOMMENDATION: It would be wise to service the cleaner and replace any worn parts, as wheels and hoses can cause plastering scaring.

Bottom Cleaner Additional Repairs
250

Auto-Fill Condition: $0

Autofill #1 Autofill #2
Pool Auto-Fill Spa Auto-Fill Auto-Fill Style Fill Speed
Yes Slow
Auto-Fill Additional Notes

OBSERVATION: There is a Anti-siphon Valve (ASV) with a battery operated control device installed as part of this mechanism, that is located to the left of the rear exit door of the home.

The ASV does NOT meet the California Plumbing Code (CBC) building code requirements for a water source for filling the swimming pool due to some of the following reasons;

1.) The device is not rated for being under constant pressure as a backflow prevention device.

2.) It appears that the ASV is located below the required minimum of 12" above the static water level of the swimming pool,

OPINION: A battery operated device that's simply connected to a fill line doesn't offer the opportunity to allow filling to correspond with the actual water drop or rise. It merely programs the filling according to the calendar schedule.

RECOMMENDATION: Install a float mechanism type auto-fill device that can correspond with the actual water drop or rise, as filling the pool via a calendar schedule can lead to over filling the pool, which can cause water to migrate and infiltrate under the pool decking.

Additionally, install a correctly sized swimming pool overflow discharge line that's connected to the landscape drainage system so that the pool doesn't become overfilled during peak storm periods of excessive rainfall.

Pool Light Condition: Good$55

Pool Light #1 Pool Light #2
Pool Light Type Distance From Electrical
Incandescent Bulb 100'
Pool Light Notes
Light is in fair condition and I would expect this light to last another 1-5 years, recommend cleaning light fixture ($55)

NEC 680.23 Underwater Luminaires.
(A) General.

(2) Transformers. Transformers for underwater luminaires shall be an isolated winding type with a grounded metal barrier between the primary and secondary windings, and shall be listed for the purpose.
(3) GFCI Protection. Branch circuits supplying underwater luminaires that operate at more than 15V shall be GFCI protected. Figure 680-15 un680-15 680-23A3.cdr
(4) Voltage Limitation. Listed underwater luminaires shall not operate on circuits over 150V.
(5) Wall-Mounted Luminaires. Listed underwater luminaires shall be installed so that the top of the luminaire lens is at least 18 in. below the normal water level.
Author’s Comment: The 18 in. requirement is to reduce the likelihood that a person hanging over the side will have their chest cavity in line with the luminaire.

Spa Light Condition: $750

Spa Light #1 Spa Light #2
Spa Light Notes
Spa Light Additional Notes

OBSERVATION: The Spa Light did not function when activating the switch at the equipment pad.

NEC 680.23 Underwater Luminaires.
(A) General.

(2) Transformers. Transformers for underwater luminaires shall be an isolated winding type with a grounded metal barrier between the primary and secondary windings, and shall be listed for the purpose.
(3) GFCI Protection. Branch circuits supplying underwater luminaires that operate at more than 15V shall be GFCI protected. Figure 680-15 un680-15 680-23A3.cdr
(4) Voltage Limitation. Listed underwater luminaires shall not operate on circuits over 150V.
(5) Wall-Mounted Luminaires. Listed underwater luminaires shall be installed so that the top of the luminaire lens is at least 18 in. below the normal water level.
Author’s Comment: The 18 in. requirement is to reduce the likelihood that a person hanging over the side will have their chest cavity in line with the luminaire.

RECOMMENDATION: Hire a licensed Electrical Contractor to investigate and possibly replace the Spa Light.

Equipment Pad


Filter Condition: Fair (Normal to High Filter Pressure - Filter Cleaning Treatment Recommended $55) $

Filter #1 Filter #2
Filter Brand Filter Model
Hayward
Filter Notes
Low Filter Pressure - Indicating Low Flow or Newly Installed Filter Element
Filter Additional Notes

Filter Pump Condition: Good$

Filter Pump #1 Filter Pump #2
Filter Pump Brand Filter Pump Model Horsepower
Jandy Variable Speed 1.5 - 3.1hp
Filter Pump Condition
The bonding wire is connected and secure
Filter Pump Notes
Filter Pump Additional Notes
Filter Pump Additional Repairs

Booster Pump Condition: $

Booster Pump #1 Booster Pump #2
Booster Pump Brand Booster Pump Model Horsepower
Booster Pump Additional Notes

Spa Jet Pump Condition: N/A$

Spa Jet Pump #1 Spa Jet Pump #2
Spa Jet Brand Spa Jet Model Horsepower
Spa Jet Additional Notes

OBSERVATION: The Pool and Spa share a common pump for filtration and heating.


Waterfall Pump Condition: N/A$

Waterfall Pump #1 Waterfall Pump #2
Waterfall Pump Brand Waterfall Pump Model Horsepower
Waterfall Pump Additional Notes

OBSERVATION: The Waterfall (Sheer Descent) and the pool's return line share a common pipe that runs through a 3-way valve, allowing the water to be diverted from the pool's wall returns to the Waterfall.

Auxiliary Pump A Condition: N/A$

Auxiliary Pump A #1 Auxiliary Pump A #2
Auxiliary Pump A Brand Auxiliary Pump A Model Horsepower
Auxiliary Pump A Additional Notes

Auxiliary Pump B Condition: N/A $

Auxiliary B #1 Auxiliary B #2
Auxiliary Pump B Brand Auxiliary Pump B Model Horsepower
Auxiliary Pump B Additional Notes

Heater Condition: N/A $

Heater #1 Heater #2
Heater Model Heater Brand
Jandy
Heater Additional Notes

OBSERVATION: The Heater was turned on and is operational.

Equipment Control System


Board & Timer Condition: Poor$7500

Board/Timer #1 Board/Timer #2
GFCI Compliant
Yes - The plug and or breaker are connected to the pool light and test and reset.
Board & Timer Additional Notes

OBSERVATION: The Timer was turned on and is operational in a bypass manual mode, the Remote Control Device was not provided.

OPINION. The Timer offers limited and acquainted operational functionality. The Isolation Valves operate manually rather than being interfaced with valve actuators that could allow remote control ability.

RECOMMENDATIONS; Upgrade the Automation Control System in order to provide a more comprehensive collaboration between Pool, Spa, Waterfall, Lighting, Cleaner and Heating capability.

ERCV $5.5K to $7.5K

Auxiliary Timer Condition: N/A $

Auxiliary Timer #1 Auxiliary Timer #2
Auxiliary Timer Additional Notes

Salt Control Systems Condition: N/A$5500

Salt Control #1 Salt Control #2
Salt System Power Detect Salt Flow Detect Salt Presence Low Salt
Salt Control System Additional Notes

OBSERVATION: The Salt System appears to be non-operational.

RECOMMENDATION: Eliminate the Salt System and replace this destructive technology with a dual application chemical free product (Ozone - UV) together with a Smart pH / ORP Doser system.

ERCV $4.5K to $5.5K

Valves & Fittings Condition: Poor$

Overall Details

Due for maintenance, small equipment pad, Required every 10-15 years, all valving must be opened, cleaned, lubricated, and re sealed to ensure longevity of equipment.
Yes, the equipment pad is UV protected by a UV protectant paint, however it is due to be re painted / recommend painting this pad to ensure long PVC piping life as well as certain equipment, The equipment appears to be in direct sunlight a large portion of the day. By simply covering the equipment with a UV mesh shade ($25-55 on Amazon + Installation) you will see approx 3x equipment life and 3x less equipment breakdown. This is recommended here.
Condition
N/A
Notes
Condition
N/A
Notes
Condition
N/A
Notes
Condition
N/A
Notes
Condition
N/A
Notes

Estimated pool repair costs based on typical seasonal construction pricing.(seasonal pricing changes $21718Est. Totals


Edit
 

Comments are closed.



Looking for something?

Use the form below to search the site:

Still not finding what you're looking for? Drop a comment on a post or contact us so we can
take care of it!

Pool Questions ? Call Us!

Do you need some swimming pool assistance? Maybe just a few questions answered ? Well give us a call, we are only a phone call away.

Sometimes you just need a second, qualified opinion.

Office: (916) 467-8038

Mobile: (916) 905-5818

Sacramento Pool Inspections & Service

We provide Weekly Pool & Spa Service, Pool Inspections, Pool Repairs, & Pool Tile Cleaning around the Sacramento Area, CA and the surrounding communities.

Swimming Pool Inspections & Service | (916) 905-5818